Nickel Alloy 205

Technical Data Sheet

 

Chemical Composition Limits
Weight%	Ni	Mg	Ti	Cu	Fe	C	Si	S	Mn
Nickel 205	99.0 min	0.01 - 0.08	0.01 - 0.05	0.15 max	0.20 max	0.15 max	0.15 max	0.008 max	0.35 max

Nickel 205 is a wrought nickel similar to Nickel 200 but with compositional adjustments to enhance the performance in electronic applications. It is most commonly used for the anodes and grids of electronic valves, magnetostrictive transducers, lead wires, transistor housings and battery cases.

Typical Mechanical Properties

Material	Tensile Strength		Yield Strength (0.2% Offset)		Elongation in 2" (%)
	psi	MPa	psi	MPa
Nickel 205	50,000	345	13,000	90	45

Mechanical Properties in the Annealed Condition

Specifications
UNS N02201 
BS 3072, BS 3073, BS 3074, BS 3075 and BS 3076 (NA12)
ASTM B160, ASTM B162, ASTM B 163, ASTM B 725 and ASTM B 730
SAE AMS 5553 Sheet, Strip
ASME SB-160, ASME SB-163 and Boiler Code Sections III, VIII, IV
DIN 17740, 17750, 17751, 17752, 17753 and 17754
Werkstoff Nr. 2.4061 and WS2.4068

Provide all grade of these alloy by different shape & size is Our expertise

For any inquiry & request, don't hesitate to contact us

 

Nickel 205 is similar to Nickel 200, but has compositional adjustments to enhance its performance in electrical and electronic applications.

Chemical Composition	Specifications	Designations	Key Features	Typical Applications
Element Min % Max % Ni + Co 99.0 - Cu - 0.15 Fe - 0.20 C - 0.15 Si - 0.15 Mn - 0.35 Mg 0.01 0.08 Ti 0.01 0.05 S - 0.05	-	W.NR 2.4061 UNS N02205 AWS 072	Similar to Nickel 200 but has compositional adjustments to enhance its performance in electrical and electronic applications	Anodes and grids of electronic valves. Lead wires. Transistor Housings. Magneto-strictive Transducers.
Density	8.89 g/cm³	0.321 lb/in³
Melting Point	1446°C	2635°F
Coefficient of Expansion	13.3 μm/m °C (20 - 100°C)	7.4 x 10-6 in/in °F (70 - 212°F)
Modulus of Rigidity	82 kN/mm²	11893 ksi
Modulus of Elasticity	207 kN/mm²	30000 ksi

 

 Provide all grade of these alloy by different shape & size is Our expertise

For any inquiry & request, don't hesitate to contact us

 

 

Electrical Resistivity
9.5 μW • cm	57 ohm • circ mil/ft

 

Thermal Conductivity
75 W/m • °C	520 btu • in/ft2 • h • °F

 

Properties
Condition	Approx. tensile strength		Approx. operating temperature
	N/mm²	ksi
Annealed	400 - 500	58 - 73	Tensile strength and elongation drop significantly at temperatures above  315°C (600°F). Service temperature is dependent on environment, load and size range.
Hard Drawn	700 - 900	102 - 131

 

Specifications
UNS N02205 
BS 3072, BS 3073, BS 3074, BS 3075 and BS 3076 (NA12)
ASTM B160, ASTM B162, ASTM B 163, ASTM B 725 and ASTM B 730
SAE AMS 5553 Sheet, Strip
ASME SB-160, ASME SB-163 and Boiler Code Sections III, VIII, IV
DIN 17740, 17750, 17751, 17752, 17753 and 17754
Werkstoff Nr. 2.4061 and WS2.4068

Availability:
NICKEL 205 Plate	NICKEL 205 Fittings	NICKEL 205 Tube / Pipe
NICKEL 205 Bar	NICKEL 205 Sheet	NICKEL 205 Coil /Strap
NICKEL 205 Fasteners / Flanges	NICKEL 205 Powder	NICKEL 205 Welding Product

 

 

Provide all grade of these alloy by different shape & size is Our expertise

For any inquiry & request, don't hesitate to contact us

 

Disclaimer
Every effort is made to ensure that technical specifications are accurate. However, technical specifications included herein should be used as a guideline only. All specifications are subject to change without notice.